program liftmaster universal keypad to chamberlain c205

PROGRAM LIFTMASTER UNIVERSAL KEYPAD TO CHAMBERLAIN C205 INSTALL
PROGRAM LIFTMASTER UNIVERSAL KEYPAD TO CHAMBERLAIN C205 MANUAL

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Īny changes or modifi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTICE: This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada license-exempt RSSs. Slide cover up, remove battery cover, and replace battery. Replace the 9-Volt battery when keypad light becomes dim or does not light up. If battery is swallowed, immediately notify doctor.NEVER allow small children near batteries.To prevent possible SERIOUS INJURY or DEATH: Test by entering your new 4-digit PIN# and press the 0 key.Enter a new 4-digit PIN# _ _ _ _, and press *.Enter the existing 4-digit PIN#, and press *.Reassemble the battery cover and keypad cover.Remove the battery and mount the keypad using screws provided.

Remove the battery cover to show mounting holes.

At the keypad cover bottom, pinch sides and firmly slide the cover from the keypad.Mount the keypad out of the path of the moving garage door, but within sight of it (4' clearance is needed for the cover).

PROGRAM LIFTMASTER UNIVERSAL KEYPAD TO CHAMBERLAIN C205 INSTALL

Install out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door.

Test by entering your 4-digit PIN, then press and hold the 0 key until door activates.

NOTE: For Genie and Overhead Door units, press the 0 key twice.

Enter your 4-digit PIN _ _ _ _, and press the 0 key.

Press and quickly release the LEARN button on the garage door opener.

If the keypad light turns off before completing this step, go back to step 3.Įnter your 4-digit PIN _ _ _ _, and press #. You have 10 seconds to complete this step.

Press and hold the * and # buttons until the keypad stops flashing.

Wayne Dalton garage door openers manufactured in 1999 to present (372.5MHz). Stanley garage door openers manufactured in 1998 to present.Ĭhamberlain, Sears Craftsman, and LiftMaster garage door openers manufactured 2011 to present. Genie Intellicode and Overhead Door garage door openers manufactured from 1995 to present (390 MHz). Genie Intellicode and Overhead Door garage door openers manufactured from 2005 to present (315 MHz). Ĭhamberlain, Sears Craftsman, LiftMaster, Master Mechanic and Do It garage door openers manufactured from 1993 to 1996. Ĭhamberlain, Sears Craftsman, LiftMaster, Master Mechanic and Do It garage door openers manufactured from 2005 to present. Linear garage door openers manufactured from 1997 to present.Ĭhamberlain, Sears Craftsman, LiftMaster, Master Mechanic and Do It garage door openers manufactured from 1997 to 2004. Garage door opener brand and manufacturing dates

Find and write your opener ID# from the list below to use in step 4.

Write a 4-digit PIN# of your choice in steps 4 and 6.

For more information go to PROGRAM THE INITIAL PIN This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. NOTE: Your garage door opener may look different. Locate the LEARN button on the garage door opener. NEVER permit anyone to cross path of moving gate or door.

ALWAYS keep gate or garage door in sight until completely closed.

Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

NEVER permit children to operate, or play with remote controls.

ALWAYS keep remote controls out of reach of children.

Install keypad within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of door.

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: Make sure the garage door opener has a working light because it is a programming indicator. If you are using this product with residential door openers, this product must be used only with door openers manufactured starting Januthat utilize photoelectric sensors located near the bottom of the door track. Read instructions thoroughly BEFORE beginning. Your universal wireless keyless entry is compatible with Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, Do It, Genie Intellicode, Overhead Door, Stanley, Wayne Dalton or Linear garage door openers with Smart/Learn button.

PROGRAM LIFTMASTER UNIVERSAL KEYPAD TO CHAMBERLAIN C205 MANUAL

LiftMaster Universal Wireless Keypad 387LM Manual

Program liftmaster universal keypad to chamberlain c205